行为级DAC波形不理想，怎么修正，求助！
录入：edatop.com 阅读：
输出本应是严格阶梯状的,出现在在输入信号上升下降时
下面是网表
- ****Start ideal 8-bit DAC Subcircuit************************************
- .subckt DAC8bit VDD VREFP VREFM trip Vout B7 B6 B5 B4 B3 B2 B1 B0
- *Change input logic signals into logic 0s or 1s
- X7 trip B7 B7L Bitlogic
- X6 trip B6 B6L Bitlogic
- X5 trip B5 B5L Bitlogic
- X4 trip B4 B4L Bitlogic
- X3 trip B3 B3L Bitlogic
- X2 trip B2 B2L Bitlogic
- X1 trip B1 B1L Bitlogic
- X0 trip B0 B0L Bitlogic
- E1 VOUT 0 VOL='(v(VREFP)-v(VREFM))/256*(v(B7L)*128+v(B6L)*64+v(B5L)*32+v(B4L)*16+v(B3L)*8+v(B2L)*4+v(B1L)*2+v(B0L)*1+1/256)'
- .ENDS
- .subckt Bitlogic trip BX BXL
- Vone one 0 DC 1.0
- Xa2 one BXL BX trip SW
- .ENDS
- ******会不会是下面这个模块不合适?**********.SUBCKT SW 1 2 3 4Gswitch 1 2 VCR PWL (1) 3 4 0V,10G 200pV ,1E-5
- R1 2 0 10G
- .ENDS
- ***main body*********
- VDD VDD 0 DC 1.0
- R2 VDD 0 10G
- VREFP VREFP 0 DC 1.0
- VREFM VREFM 0 DC 0.0
- VTRIP TRIP 0 DC 0.0
- VB7 B7 0 DC 0 pulse(1.0 0 0 200p 200p 1279.8n 2560n)
- VB6 B6 0 DC 0 pulse(1.0 0 0 200p 200p 639.8n 1280n)
- VB5 B5 0 DC 0 pulse(1.0 0 0 200p 200p 319.8n 640n)
- VB4 B4 0 DC 0 pulse(1.0 0 0 200p 200p 159.8n 320n)
- VB3 B3 0 DC 0 pulse(1.0 0 0 200p 200p 79.8n 160n)
- VB2 B2 0 DC 0 pulse(1.0 0 0 200p 200p 39.8n 80n)
- VB1 B1 0 DC 0 pulse(1.0 0 0 200p 200p 19.8n 40n)
- VB0 B0 0 DC 0 pulse(1.0 0 0 200p 200p 9.8n 20n)
- Xa1 VDD VREFP VREFM trip Vout B7 B6 B5 B4 B3 B2 B1 B0 DAC8bit
- R1 VOUT 0 10G
- .OPTION LIST NODE POST
- .OP
- .option runlvl=0
- .TRAN 200p 2.6u
- .PRINT DC v(Vout)
- .END
期待大家的帮助，谢谢！
越高位变化时，毛刺越明显
修改后：
.SUBCKT SW 1 2 3 4Gswitch 1 2 VCR PWL (1) 3 4 0V,10G 200pV ,1E-5
R1 2 0 1E-4
.ENDS
波形没有明显变化
mmmmmmmm
Set runlvl=6 to get the most accuracy but at the cost of reduced simulation speed！
申明：网友回复良莠不齐，仅供参考。如需专业解答，请学习本站推出的微波射频专业培训课程。
上一篇：如何用calculator计算瞬态波形的最大值
下一篇：寻找decimation filter的专家，私活报酬丰厚
