• 易迪拓培训,专注于微波、射频、天线设计工程师的培养
首页 > 手机设计 > 手机射频设计讨论 > MTK 问题前辈 (关于校准)

MTK 问题前辈 (关于校准)

录入:edatop.com     点击:
用ATE校准,总是出现“AFC Calibration fail=>501”,用的TC是6139+77518。用META校准AFC能通过,但是校到TXIQ时,就停在那里,出现红色的提示“Tx IQ Calibration progress”.用“2PCL”校准时,校到TX时会出现“Tx PCL Calibration send NB Fail”,用“full PCL”校准校到Tx时,会出现“Tx power control level check fail”,不知道是怎么回事,强制发射各项指标都很正常,我是刚接触MTK ,问了一直在做的同事说是“meta_6225.CFG”配置错误了,我用的主芯片是6223,我把“ meta_6225.CFG”内容附出来,让版内的大侠分析一下,不甚感激,谢谢!
AFC_ARFCN = 70
N_AFC = 10
DAC1 = 4000
DAC2 = 5000
[Crystal AFC Calibration]
CRYSTAL_AFC_BAND = GSM
CRYSTAL_AFC_ARFCN = 20
CRYSTAL_AFC_GSM850_PCL = 12
CRYSTAL_AFC_GSM900_PCL = 12
CRYSTAL_AFC_DCS1800_PCL = 12
CRYSTAL_AFC_PCS1900_PCL = 12
CRYSTAL_AFC_CAL_DAC = 4000
CRYSTAL_AFC_CHECK_DAC1 = 0
CRYSTAL_AFC_CHECK_DAC2 = 8000
CRYSTAL_AFC_MIN_FREQ_ERR_PPM = -18.0
CRYSTAL_AFC_MAX_FREQ_ERR_PPM = 18.0
CRYSTAL_AFC_FREQ_ERR_MEASUSE_COUNT = 10
CRYSTAL_AFC_TRX_OFFSET_RECURSIVE_TIMES = 20
[RX path loss table]
GSM850_MAX_RX_LOSS = 5.0,5.0,5.0,5.0,5.0,3.0,3.0,3.0,3.0,3.0,3.0,3.0,
GSM850_MIN_RX_LOSS = -5.0,-5.0,-5.0,-5.0,-3.0,-3.0,-3.0,-3.0,-3.0,-3.0,-3.0,-3.0,
GSM900_MAX_RX_LOSS = "5.0,4.0,4.0,4.0,4.0,4.0,4.0,4.0,5.0,5.0,5.0,5.0,"
GSM900_MIN_RX_LOSS = "-5.0,-4.0,-4.0,-4.0,-4.0,-4.0,-4.0,-4.0,-5.0,-5.0,-5.0,-5.0,"
DCS1800_MAX_RX_LOSS = "5.0,5.0,5.0,5.0,5.0,5.0,5.0,5.0,5.0,5.0,5.0,5.0,"
DCS1800_MIN_RX_LOSS = "-5.0,-5.0,-5.0,-5.0,-5.0,-5.0,-5.0,-5.0,-5.0,-5.0,-5.0,-5.0,"
PCS1900_MAX_RX_LOSS = "5.0,5.0,5.0,5.0,5.0,5.0,5.0,5.0,5.0,5.0,5.0,5.0,"
PCS1900_MIN_RX_LOSS = "-5.0,-5.0,-5.0,-5.0,-5.0,-5.0,-5.0,-5.0,-5.0,-5.0,-5.0,-5.0,"
[AFC table]
MAX_INIT_AFC_DAC = 7000
MIN_INIT_AFC_DAC = 2000
MAX_AFC_SLOPE = 10.0
MIN_AFC_SLOPE = 1.0
[IP2 table]
IP2_arfcn_C0_GSM850 = 220
IP2_arfcn_C0_GSM = 100
IP2_arfcn_C0_DCS = 730
IP2_arfcn_C0_PCS = 690
IP2_CAL_P_DL_ON_SKY = -30
IP2_CAL_P_DL_ON_MT = -25
IP2_CAL_P_DL_OFF_MT = -120
IP2_GAIN = 65
IP2_N_PM = 200
IP2_M_PM = 4
IP2_ICORRECTION1_SKY74045 = -40
IP2_QCORRECTION1_SKY74045 = -40
IP2_ICORRECTION2_SKY74045 = 40
IP2_QCORRECTION2_SKY74045 = 40
IP2_ICORRECTION1_SKY74117 = -40
IP2_QCORRECTION1_SKY74117 = -40
IP2_ICORRECTION2_SKY74117 = 40
IP2_QCORRECTION2_SKY74117 = 40
IP2_AMCODEI1 = 64
IP2_AMCODEQ1 = 64
IP2_AMCODEI2 = 191
IP2_AMCODEQ2 = 191
IP2_MAX_IDC = 5000
IP2_MAX_QDC = 5000
IP2_CHECK_P_DL_ON = -22
IP2_CHECK_P_DL_OFF = -120
[TX IQ table]
TX_IQ_MEASUREMENT_COUNT = 20
TX_IQ_BAND = GSM
TX_IQ_ARFCN = 70
TX_IQ_PCL = 10
TX_IQ_DC_OFFSET_MAX = -40
TX_IQ_GAIN_IMBALANCE_MAX = -40
; The following setting is for MT6140B
TX_IQ_BAND_HIGH = DCS
TX_IQ_ARFCN_HIGH = 700
TX_IQ_PCL_HIGH = 10
TX_IQ_DC_OFFSET_MAX_HIGH = -40
TX_IQ_GAIN_IMBALANCE_MAX_HIGH = -40
[TX PCL table]
GSM850_CAL_PCL = 17, 12, 5,
GSM850_2CAL_PCL = 19, 5,
GSM850_PCL = 19,18,17,16,15,14,13,12,11,10,9,8,7,6,5,
GSM850_CHECK_PCL = 19,18,17,16,15,14,13,12,11,10,9,8,7,6,5,
GSM850_MAX_P = 6,8,10,12,14,16,18,20,22,24,26,28,30,31.5,32.6,
GSM850_WANTED_P = 5.2,7,9,11,13,15,17,19,21,23,25,27,29,30.8,32.2,
GSM850_MIN_P = 4,6,8,10,12,14,16,18,20,22,24,26,28,30,31.7,
GSM850_C = 5,5,5,5,5,5,5,5,5,5,5,5,5,5,5,5,
GSM850_CORRECTION = -0.4,0,0.2,0.2,0.2,0.1,0.1,0,-0.1,-0.1,0,0,-0.1,-0.1,0,
GSM850_EPSK_CAL_PCL = 17, 12, 5,
GSM850_EPSK_2CAL_PCL = 19, 5,
GSM850_EPSK_PCL = 19,18,17,16,15,14,13,12,11,10,9,8,7,6,5,
GSM850_EPSK_CHECK_PCL = 19,18,17,16,15,14,13,12,11,10,9,8,7,6,5,
GSM850_EPSK_MAX_P = 6,8,10,12,14,16,18,20,22,24,26,27,27,27,27,
GSM850_EPSK_WANTED_P = 5.2,7,9,11,13,15,17,19,21,23,25,26.3,26.3,26.3,26.3,
GSM850_EPSK_MIN_P = 4,6,8,10,12,14,16,18,20,22,24,25.8,25.8,25.8,25.8,
GSM850_EPSK_C = 5,5,5,5,5,5,5,5,5,5,5,5,5,5,5,5,
GSM850_EPSK_CORRECTION = -0.4,0,0.2,0.2,0.2,0.1,0.1,0,-0.1,-0.1,0,0,-0.1,-0.1,0,
GSM900_CAL_PCL = 17, 12, 5,
GSM900_2CAL_PCL = 19, 5,
GSM900_PCL = 19,18,17,16,15,14,13,12,11,10,9,8,7,6,5,
GSM900_CHECK_PCL = 19,18,17,16,15,14,13,12,11,10,9,8,7,6,5,
GSM900_MAX_P = 6,8,10,12,14,16,18,20,22,24,26,28,30,31.5,32.6,
GSM900_WANTED_P = 5.2,7,9,11,13,15,17,19,21,23,25,27,29,30.8,32.3,
GSM900_MIN_P = 4,6,8,10,12,14,16,18,20,22,24,26,28,30,32,
GSM900_C = 5,5,5,5,5,5,5,5,5,5,5,5,5,5,5,5,
GSM900_CORRECTION = 0,0.3,0.4,0.5,0.6,0.6,0.5,0.5,0.5,0.4,0.3,0.5,0.3,0.4,0,
GSM900_EPSK_CAL_PCL = 17, 12, 5,
GSM900_EPSK_2CAL_PCL = 19, 5,
GSM900_EPSK_PCL = 19,18,17,16,15,14,13,12,11,10,9,8,7,6,5,
GSM900_EPSK_CHECK_PCL = 19,18,17,16,15,14,13,12,11,10,9,8,7,6,5,
GSM900_EPSK_MAX_P = 6,8,10,12,14,16,18,20,22,24,26,27,27,27,27,
GSM900_EPSK_WANTED_P = 5.2,7,9,11,13,15,17,19,21,23,25,26.3,26.3,26.3,26.3,
GSM900_EPSK_MIN_P = 4,6,8,10,12,14,16,18,20,22,24,25.8,25.8,25.8,25.8,
GSM900_EPSK_C = 5,5,5,5,5,5,5,5,5,5,5,5,5,5,5,5,
GSM900_EPSK_CORRECTION = 0,0.2,0.3,0.4,0.5,0.5,0.5,0,0.5,0.5,0.6,0,0,0,0,
DCS1800_CAL_PCL = 13, 8, 1,
DCS1800_2CAL_PCL = 15, 0,
DCS1800_PCL = 15,14,13,12,11,10, 9, 8, 7, 6, 5,4,3,2,1,0,
DCS1800_CHECK_PCL= 15,14,13,12,11,10, 9, 8, 7, 6, 5,4,3,2,1,0,
DCS1800_MAX_P = 2, 3.5, 5,7,9,11,13,15,17,19,21,23,25,27,28.5,30,
DCS1800_WANTED_P = 1.2,2.5,4,6,8,10,12,14,16,18,20,22,24,26,27.8,29.2,
DCS1800_MIN_P = -0.5,1.5,3,5,7,9,11,13,15,17,19,21,23,25,27,28.7,
DCS1800_C = 5,5,5,5,5,5,5,5,5,5,5,5,5,5,5,5,
DCS1800_CORRECTION = 0,0,0.5,0.4,0.6,0.6,0.6,0.6,0.7,0.5,0.4,0.4,0.3,0.2,0,0,
DCS1800_EPSK_CAL_PCL = 13, 8, 1,
DCS1800_EPSK_2CAL_PCL = 15, 0,
DCS1800_EPSK_PCL = 15,14,13,12,11,10, 9, 8, 7, 6, 5,4,3,2,1,0,
DCS1800_EPSK_CHECK_PCL= 15,14,13,12,11,10, 9, 8, 7, 6, 5,4,3,2,1,0,
DCS1800_EPSK_MAX_P = 2,3.5,5,7,9,11,13,15,17,19,21,23,25,26.1,26.1,26.1,
DCS1800_EPSK_WANTED_P = 1.2,2.5,4.3,6,8,10,12,14,16,18,20,22,24,25.3,25.3,25.3,
DCS1800_EPSK_MIN_P = -0.5,1.5,3.5,5,7,9,11,13,15,17,19,21,23,24.8,24.8,24.8,
DCS1800_EPSK_C = 5,5,5,5,5,5,5,5,5,5,5,5,5,5,5,5,
DCS1800_EPSK_CORRECTION = 0.3,0.3,0.5,0.4,0.5,0.5,0.5,0.5,0.5,0.5,0.5,0.5,0.3,0,0,0,
PCS1900_CAL_PCL = 13, 8, 1,
PCS1900_2CAL_PCL = 15, 0,
PCS1900_PCL = 15,14,13,12,11,10, 9, 8, 7, 6, 5,4,3,2,1,0,
PCS1900_CHECK_PCL = 15,14,13,12,11,10, 9, 8, 7, 6, 5,4,3,2,1,0,
PCS1900_MAX_P = 2, 3.5, 5,7,9,11,13,15,17,19,21,23,25,27,28.5,30,
PCS1900_WANTED_P = 1.2,2.5,4,6,8,10,12,14,16,18,20,22,24,26,27.8,29.2,
PCS1900_MIN_P = -0.5,1.5,3,5,7,9,11,13,15,17,19,21,23,25,27,28.7,
PCS1900_C = 5,5,5,5,5,5,5,5,5,5,5,5,5,5,5,5,
PCS1900_CORRECTION = 0,0.2,0.3,0.4,0.5,0.5,0.5,0.5,0.5,0.5,0.5,0.5,0.5,0.4,0,0,
PCS1900_EPSK_CAL_PCL = 13, 8, 1,
PCS1900_EPSK_2CAL_PCL = 15, 0,
PCS1900_EPSK_PCL = 15,14,13,12,11,10, 9, 8, 7, 6, 5,4,3,2,1,0,
PCS1900_EPSK_CHECK_PCL = 15,14,13,12,11,10, 9, 8, 7, 6, 5,4,3,2,1,0,
PCS1900_EPSK_MAX_P = 2,3.5,5,7,9,11,13,15,17,19,21,23,25,26.1,26.1,26.1,
PCS1900_EPSK_WANTED_P = 1.2,2.5,4.3,6,8,10,12,14,16,18,20,22,24,25.3,25.3,25.3,
PCS1900_EPSK_MIN_P = -0.5,1.5,3.5,5,7,9,11,13,15,17,19,21,23,24.8,24.8,24.8,
PCS1900_EPSK_C = 5,5,5,5,5,5,5,5,5,5,5,5,5,5,5,5,
PCS1900_EPSK_CORRECTION = 0,0.2,0.3,0.4,0.5,0.5,0.5,0.5,0.5,0.5,0.5,0.5,0.3,0,0,0,
TSC = 5
Recursive Times = 10
APC Delta = 0.1
SKY77328_DAC_Delta=10
SKY77328_GSM850_M= 16.8
SKY77328_GSM850_TARGET_PCL= 19
SKY77328_GSM850_MAX_HIGH_APC_DC_OFFSET_P = -3.5
SKY77328_GSM850_WANTED_HIGH_APC_DC_OFFSET_P= -4
SKY77328_GSM850_MIN_HIGH_APC_DC_OFFSET_P = -4.5
SKY77328_GSM850_MAX_LOW_APC_DC_OFFSET_P = -3.5
SKY77328_GSM850_WANTED_LOW_APC_DC_OFFSET_P = -4
SKY77328_GSM850_MIN_LOW_APC_DC_OFFSET_P = -4.5
SKY77328_GSM900_M= 16.8
SKY77328_GSM900_TARGET_PCL= 19
SKY77328_GSM900_MAX_HIGH_APC_DC_OFFSET_P = -3.5
SKY77328_GSM900_WANTED_HIGH_APC_DC_OFFSET_P= -4
SKY77328_GSM900_MIN_HIGH_APC_DC_OFFSET_P = -4.5
SKY77328_GSM900_MAX_LOW_APC_DC_OFFSET_P = -3.5
SKY77328_GSM900_WANTED_LOW_APC_DC_OFFSET_P = -4
SKY77328_GSM900_MIN_LOW_APC_DC_OFFSET_P = -4.5
SKY77328_DCS1800_M = 17.78
SKY77328_DCS1800_TARGET_PCL = 15
SKY77328_DCS1800_MAX_HIGH_APC_DC_OFFSET_P = -3.5
SKY77328_DCS1800_WANTED_HIGH_APC_DC_OFFSET_P = -4
SKY77328_DCS1800_MIN_HIGH_APC_DC_OFFSET_P = -4.5
SKY77328_DCS1800_MAX_LOW_APC_DC_OFFSET_P = -3.5
SKY77328_DCS1800_WANTED_LOW_APC_DC_OFFSET_P = -4
SKY77328_DCS1800_MIN_LOW_APC_DC_OFFSET_P = -4.5
SKY77328_PCS1900_M = 17.78
SKY77328_PCS1900_TARGET_PCL = 15
SKY77328_PCS1900_MAX_HIGH_APC_DC_OFFSET_P = -3.5
SKY77328_PCS1900_WANTED_HIGH_APC_DC_OFFSET_P = -4
SKY77328_PCS1900_MIN_HIGH_APC_DC_OFFSET_P =-4.5
SKY77328_PCS1900_MAX_LOW_APC_DC_OFFSET_P = -3.5
SKY77328_PCS1900_WANTED_LOW_APC_DC_OFFSET_P = -4
SKY77328_PCS1900_MIN_LOW_APC_DC_OFFSET_P = -4.5
[TX DC offset table]
TX_DC_0FFSET_BAND = GSM
TX_DC_0FFSET_ARFCN = 70
TX_DC_0FFSET_PCL = 10
TX_DC_0FFSET_MAX = -40
[TX IQ imbalance table]
TX_IQ_IMBALANCE_BAND = GSM
TX_IQ_IMBALANCE_ARFCN = 70
TX_IQ_IMBALANCE_PCL = 10
TX_IQ_IMBALANCE_MAX = -40
[Phase error table]
PHASE_ERROR_BAND = 0
PHASE_ERROR_ARFCN = 70
PHASE_ERROR_PCL = 10
PHASE_ERROR_RMS_ERROR = 1.5
[ADC table]
ADC_V1 = 3400
ADC_V2 = 4200
NORMAL_VOLTAGE = 3800
CURRENT_LIMIT = 2000
MAX_BATTERY_ADC_SLOPE = 5550.0
MIN_BATTERY_ADC_SLOPE = 5250.0
MAX_BATTERY_ADC_OFFSET = 1000000
MIN_BATTERY_ADC_OFFSET = -1000000
BATTERY_CHANNEL = 0
CHARGER_CHANNEL = 1
ADC_RESISTANCE = 0.33
MAX_VOLTAGE_DIFFERENCE = 0.04
MAX_CURRENT_DIFFERENCE = 0.04
ADC_MEASUREMENT_COUNT = 1000
[WiFi TX power 2.4G]
TX power CCK = 40,40,40,40,40,40,40,40,40,40,40,40,40,40
TX power OFDM = 55,55,55,55,55,55,55,55,55,55,55,55,55,55
[WiFi common]
WiFi_Support = 0x06
[WiFi TX power table]
802.11B_CAL_CHANNEL = 2412,2442,2484,
802.11B_CHECK_CHANNEL = 2412,2442,2484,
CCK_MAX_P = 16.5
CCK_WANTED_P = 15.0
CCK_MIN_P = 13.5
CCK_C = 1
CCK_Delta = 0.3
CCK_CAL_RATE = 1.0
CCK_CHECK_RATE = 1.0
802.11G_CAL_CHANNEL = 2412,2442,2484,
802.11G_CHECK_CHANNEL = 2412,2442,2484,
OFDM_MAX_P = 13.5
OFDM_WANTED_P = 12.0
OFDM_MIN_P = 10.5
OFDM_C = 1
OFDM_Delta = 0.3
OFDM_CAL_RATE = 54.0
OFDM_CHECK_RATE = 54.0
Recursive Times = 10

怎么没有跟呢,自己先顶一下吧

本人不做这方面。看LZ也XIN KU 顶一下了

没问题

申明:网友回复良莠不齐,仅供参考。

上一篇:3G WCDMA扰码与OVSF码的区别(附图)
下一篇:800MCDMA能改频到450M吗?

手机天线设计培训教程详情>>

手机天线设计培训教程 国内最全面、系统、专业的手机天线设计培训课程,没有之一;是您学习手机天线设计的最佳选择...【More..

易迪拓培训课程列表详情>>

我们是来自于研发一线的资深工程师,专注并致力于射频、微波和天线设计工程师的培养。

  网站地图