双面板灌铜问题

最近做了一块新的双面板的板子,在灌铜出现如下记事本信息,可以灌铜:
THERMAL RELIEF ERRORS REPORT -- QS-MSPD03-A1.pcb -- Sat Feb 07 06:51:27 2009
Drilled pads with Nondrilled pads with
less than 50% thermal extensionsless than 50% thermal extensions
Report of Thermal Spokes Generator.
On Bottom:
CON1.59 (101.294, 22.81894) # = 0
J1.6(1.35567, 81.92433) # = 0
J1.5(1.35567, 73.32433) # = 0
On Top:
U3.28 (38.24533, 6.996) # = 0
U2.91 (48.22467, 46.587) # = 1
U2.33 (37.29967, 29.662) # = 0
U2.30 (36.09967, 29.662) # = 0
U4.38 (7.21033, 33.401) # = 0
U2.115(43.29967, 55.912) # = 1
C121.1(24.97, 61.60933) # = 1
C65.2 (31.38433, 61.60933) # = 0
C34.2 (26.72167, 61.60933) # = 0
CN8.1 (77.11, 45.22633) # = 0
C26.1 (96.876, 50.80367) # = 1
CN1.2 (92.893, 81.84633) # = 1
C88.1 (38.54833, 65.999) # = 1
C18.1 (83.90833, 14.99367) # = 1
R12.2 (82.59033, 9.459) # = 1
C107.2(108.83067, 24.37833) # = 0
C116.1(104.612, 23.685) # = 1
CN7.29(114.48167, 46.79733) # = 0
CN6.16(73.89233, 27.71833) # = 0
R117.2(97.751, 34.52467) # = 0
Q11.2 (52.23133, 65.47267) # = 1
C91.1 (65.06753, 36.39501) # = 1
C57.2 (57.362, 22.507) # = 0
C113.2(71.72767, 30.46967) # = 1
U7.7(21.968, 23.83633) # = 0
R20.2 (100.10933, 8.49433) # = 0
C67.2 (21.47, 20.647) # = 0
R127.2(97.876, 36.15167) # = 0
C80.2 (32.66633, 17.85967) # = 0
CN6.7 (73.89233, 23.21833) # = 0
C40.2 (17.489, 50.371) # = 0
CN8.21(77.11, 55.22633) # = 0
C39.2 (109.961, 20.211) # = 0
CN8.26(77.11, 57.72633) # = 1
C21.1 (69.32467, 6.146) # = 0
D2.2(93.05307, 8.08817) # = 1
C51.2 (53.16633, 47.10233) # = 0
ZD1.2 (100.73467, 18.71433) # = 1
C89.2 (49.505, 61.53967) # = 1
R59.1 (39.99533, 63.06367) # = 1
C82.1 (37.22967, 63.06367) # = 0
C81.1 (38.589, 63.06367) # = 0
R64.1 (35.84823, 63.06357) # = 0
R6.2(19.39533, 61.16) # = 1
C96.2 (50.354, 79.19) # = 1
C53.2 (17.92133, 45.94567) # = 0
C86.2 (41.31433, 63.06367) # = 1
C87.1 (45.903, 60.085) # = 1
CN8.27(79.41, 43.27633) # = 0
C124.1(103.66167, 84.20467) # = 0
U8.3(98.70567, 86.39) # = 0
C45.2 (14.993, 46.32267) # = 0
U4.13 (8.21033, 13.801) # = 0
R33.1 (16.271, 52.34533) # = 0
C27.2 (17.80433, 55.72233) # = 0
C78.2 (42.75068, 59.99373) # = 0
CN5.1 (3.179, 37.31367) # = 1
C62.2 (57.127, 5.22033) # = 0
U3.52 (57.44533, 6.996) # = 0
U3.41 (48.64533, 6.996) # = 1
U3.46 (52.64533, 6.996) # = 0
U2.104(48.22467, 51.787) # = 1
C75.2 (40.14312, 59.99373) # = 0
U2.130(37.29967, 55.912) # = 0
U2.175(21.97467, 48.587) # = 1
U2.168(21.97467, 51.387) # = 1
Total Drilled pads:2 Total Nondrilled pads: 67
Report of Violating Thermal Spokes Remover.
On Top:
U2.16 (30.49967, 29.662) # = 0
U2.91 (48.22467, 46.587) # = 0
U2.101(48.22467, 50.587) # = 0
U2.104(48.22467, 51.787) # = 0
U2.115(43.29967, 55.912) # = 0
U2.121(40.89967, 55.912) # = 1
U2.168(21.97467, 51.387) # = 0
U2.175(21.97467, 48.587) # = 0
Total Drilled pads:0 Total Nondrilled pads:8
请教高手原因?

这个好像没有问题吧，一般铺完都会出现这样的结果，只要保证Total Drilled pads这项为零。个人见解，

CON1.59 (101.294, 22.81894) # = 0 表示这个pad(第59个pad)没有连接到ground,在检查的时候要连一段线到gnd之后,DRC才检测ok.

這是spoke少於兩個的警告,一般都不太去理會..

SMT元件铺铜不能满,是有问题的

已经搞定了,原来很简单

很简单是怎么搞定的？