关于orcad出网络表带value的问题

(Orcad 2 pads2007)的网络表时,却出现以下的问题,各位请问应该怎么解决呢?谢谢！
Reading file --F:adsl.asc
*Unspecified or unsupported version of ASCII file
*PADS2000*
Bad part mirror value -1
C12 DIP-CAP,470PF - 5KV - Y2
*Bad *PART* ascii data line format
C24 0603,0.1UF 10%
*Bad *PART* ascii data line format
C25 0603,0.1UF 10%
*Bad *PART* ascii data line format
C26 0603,0.1UF 10%
*Bad *PART* ascii data line format
C73 0603,CAP NP
*Bad *PART* ascii data line format
C75 0603,CAP NP
Bad part mirror value -1
C9 DIP-CAP,470PF - 5KV - Y2
*Bad *PART* ascii data line format
R39 0603,24K 5%
*Bad *PART* ascii data line format
SW1 SW-8,SW SLIDE-DP3T
*Bad *PART* ascii data line format
SW2 SIP-3P,SW SLIDE-SPDT
*Bad *PART* ascii data line format
SW3 SIP-3P,SW SLIDE-SPDT
*Bad *PART* ascii data line format
SW4 SIP-3P,SW SLIDE-SPDT
*Part name not found C26
U2.4 C26.1 C23.2
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal N253543
*Part name not found SW4
SW4.3 R113.1
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal N1817995
*Part name not found SW3
SW3.3 U10.3
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal N1842163
*Part name not found SW4
R112.1 SW4.1
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal N1800505
*Part name not found SW1
SW1.5 RV3.1 D12.1
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal N10263
*Part name not found SW1
SW1.6 J7.1
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal N09585
*Part name not found C75
U11.8 U13.1 C75.1
*Part name not found SW2
SW2.2 U12.13
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal N3170318
*Part name not found SW3
SW3.2 U12.12
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal N3170741
*Part name not found C12
C12.1 RV2.1 RV1.2 T1.9 J1.4
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal N150942
*Part name not found C9
C9.2 C12.2 J1.10 J1.9 J3.37 J3.36 J3.35 J3.34
*Part name not found R39
U2.51 U2.43 R39.2 C26.2 C24.2 C29.2 C31.2 C32.2
*Part name not found C25
U1.57 U1.48 U1.21 C6.2 C13.2 C25.2 C30.2 C33.2
*Part name not found C73
C72.2 U11.7 C73.2 U12.7 U10.7 U13.8
*Part name not found C25
U2.5 C25.1 C23.1
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal N253227
*Part name not found C24
U2.6 C24.1
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal N252913
*Part name not found R39
U2.24 R39.1
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal N252601
*Part name not found C9
T1.16 C9.1 RV1.1 RV2.2 J1.3
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal N150517
*Part name not found SW2
U1.76 D8.2 SW2.3
*Part name not found SW3
SW3.1 SW2.1
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal N1889636
*Part name not found C73
U11.2 C73.1 SW4.2
*Bad *CONNECTION* ascii data format, nets must contain more than one pin. Signal N1800965
*Part name not found C75
U11.12 U11.13 R116.2 C75.2
Warning: deleting signal N253543
Warning: deleting signal N1817995
Warning: deleting signal N1842163
Warning: deleting signal N1800505
Warning: deleting signal N10263
Warning: deleting signal N09585
Warning: deleting signal N3170318
Warning: deleting signal N3170741
Warning: deleting signal N150942
Warning: deleting signal N253227
Warning: deleting signal N252913
Warning: deleting signal N252601
Warning: deleting signal N150517
Warning: deleting signal N1889636
Warning: deleting signal N1800965
**INPUT WARNINGS FOUND**
如果不带value出网络表则没有问题;出网络表的设置如图所示

ORCAD不能有非法字符。请楼主改一下

那为什么不带value出网络表则没有问题;

呵呵，比如你的值有空格间距或非法字符，最好用／这样的表示

谢谢上面两位