• 易迪拓培训,专注于微波、射频、天线设计工程师的培养
首页 > ADS > ADS FAQ > ADS ATF36163 pHEMT model simulation warninghelp plz

ADS ATF36163 pHEMT model simulation warninghelp plz

录入:edatop.com    点击:
i have downloaded the .zap file of ATF36163 from avago website.but when i start the DC simulation with ADS2008,it said that :

Simulation / Synthesis Messages

Warning detected by hpeesofsim during DC analysis `DC1'.
Matrix is singular (detected at node or branch `X1.L56.i').

Warning detected by hpeesofsim during DC analysis `DC1'.
Circuit converged after a virtual resistance of 1 TOhms
was added between each node and ground, and a virtual
resistance of 1 pOhms was inserted in each current branch.
Possible causes include floating nodes or missing ground.

Warning detected by hpeesofsim during DC analysis `DC1'.
A virtual resistance of 1 pOhms
was added to branch X1.L56.i.

Warning detected by hpeesofsim during DC analysis `DC1'.
A virtual resistance of 1 pOhms
was added to branch X1.L9.i.

Warning detected by hpeesofsim during DC analysis `DC1'.
A virtual resistance of 1 pOhms
was added to branch X1.L67.i.

Status / Summary

hpeesofsim (*) 331.200 May 6 2008 (built: 05/06/08 00:26:15)
Copyright Agilent Technologies, 1989-2008.

CT Sweep1[1] <D:\users\default\atf36163_prj\networks\1> VGS=(-1->0)

DC Sweep1[1].DC1[1/21] <D:\users\default\atf36163_prj\networks\1> VGS=-1 VDS=(0->5)

i have no idea about this.someone give me some help!~
here is the ATF36163 .zap file&my simulation prj.

No test setup is shared.
The attachment is only model.

PS:
Its nothing wrong as it is warning only.
The reasons are,
Simulatior is computing for DC then the reactance for L is zero, simulator does not act on zero ohm and hence replaced with peco ohm.
Similarly for Cap the reactance is infinity, which is replaced with tera ohm.

If you do AC analysis then these warning will not appear

here is the DC_simulation &AC_simulation with ADS.
the warning is still the same!~

Simulation / Synthesis Messages

Warning detected by hpeesofsim during DC analysis `DC1'.
Matrix is singular (detected at node or branch `Q1.L9.i').
Warning detected by hpeesofsim during DC analysis `DC1'.
Circuit converged after a virtual resistance of 1 TOhms
was added between each node and ground, and a virtual
resistance of 1 pOhms was inserted in each current branch.
Possible causes include floating nodes or missing ground.

Status / Summary

hpeesofsim (*) 350.500 Feb 19 2009 (built: 02/19/09 22:31:44)
Copyright Agilent Technologies, 1989-2008.

DC DC1[1] <C:\users\default\X_prj\networks\s_parameter>
.
..

DC convergence achieved in 79 iterations.

AC AC1[1] <C:\users\default\X_prj\networks\s_parameter> freq=(2 GHz->16 GHz)
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,

Resource usage:
Total stopwatch time: 1.30 seconds.

-------------------------------------------------------------------------------
Simulation finished: dataset `s_parameter' written in:
`C:\users\default\X_prj/data'
-------------------------------------------------------------------------------

what should i do?help plz.

申明:网友回复良莠不齐,仅供参考。如需专业帮助,请学习易迪拓培训专家讲授的ADS视频培训课程

上一篇:what is the Zo in ADS momentum?
下一篇:thick substrate simulation in ads

ADS培训课程推荐详情>>

  网站地图