- 易迪拓培训,专注于微波、射频、天线设计工程师的培养
ADS simulation of a voltage dependant resistor
I have tried for several hours but no progress so far.
I saw in another post that Z1P_Eqn component might be used but I am not an expert user by any means, I mainly use SPICE.
Thanks
Describe it by SDD or Verilog-A.
Hi Pancho, thanks for reply.
I am doing this with a SDD2P component at the moment which means that the resistor element I was looking for is a current source which is not quite the same.
I dont know anything about verilog.
What I am trying to do is make a simple rf power fet model based on a votlage variable resistor whose resistance varies according to the input voltage. It is so easy to do this in Spice.
The way to create a frequency dependent resistor in ADS is to use the Z1P_Eqn component.
ADS : How to simulate frequency dependent resistor (and inductance)
Hi RealAEL, thanks for reply. However I am trying to make a voltage dependent resistor which I can then use as a simple model of a RF MOSFET where the instantaneous gate voltage changes the resistance value according to a simple equation.
In free LTspice I can do this in seconds, but ADS has me stumped.
It's very easy.
Attached example is a voltage controled resistor where
R=Roff for Vc<Voff
R=Rx_hspice(Vc) for Voff<=Vc<=Von
R=Ron for Vc>Von
ADS is more powerful and versatile in ability of behavioral description than SPICE.
Thanks pancho, I could not find the attachment, where is it located?
ok I see it now, I will give it a try. Thanks again !
Pancho, thanks for reply.
In my ADS I only have SDD2P not SDD2Pform, not sure if they are different.
Can I add all these equations with SDD2P? I am an ADS beginner.
Also I am not following the math.
None of the variable names are defined so I am mostly guessing what you are doing.
If you assume that the input voltages are always positive would that remove many of the confusing equations?
Use SDD2P.
Attached figure is from MDS which is one of ancestors of ADS.
Currently I use Verilog-A instead of SDD even in ADS.
We can use any behavioral models in any vendor's simulator such as HSPICE, Spectre and Eldo, etc. if we describe them by Verilog-A.
http://edadocs.software.keysight.com...he+SDD+and+UCM
Not necessary.
I prepaire two ypes of resistor for Voff<=Vc<=Von.
(1) Rx_hspice(Vc)
(2) Rx_pspice(Vc)
If you don't use Rx_pspice(Vc), you don't have to write related variables.
Show me equations which you want to implement.
Can you understand ADS netlist ?
All variables are defined in schematic.
I use Ron, Roff, Von and Voff as pass parameters.
Again show me equations which you want to implement.
Thanks Pancho,
I will get back to this but I was able to move forward with the level 3 MOSFET model.
I wanted to ask if anyone knows how to remove all the left over net labels on the schematic once a wire is deleted?
Actually I was not even able to work out how to add these equations to the SDD2P, I am beginner.
Surely Read documents of ADS.
http://edadocs.software.keysight.com...efined+Devices
http://www.designers-guide.org/Forum...=1458586399/#1
I[1,0]=0
I[2,0]=_v2/Rsw
User "VAR Component" instead of "EQUATION".
Is there any relation to this thread ?
Your questions are no more than easy usage of ADS schematic editor and have no relation to this thread.
If you have questions which have no relation to this thread, start different thread.
Just trying to save starting a new thread over every detail. Also for some reason I cannot post here yet.
申明:网友回复良莠不齐,仅供参考。如需专业帮助,请学习易迪拓培训专家讲授的ADS视频培训课程。
上一篇:Coupled oscillator array simulation using ADS
下一篇:Questions about PA simulation in ADS
国内最全面、最专业的Agilent ADS培训课程,可以帮助您从零开始,全面系统学习ADS设计应用【More..】
- Agilent ADS教学培训课程套装
- 两周学会ADS2011、ADS2013视频教程
- ADS2012、ADS2013射频电路设计详解
- ADS高低阻抗线微带滤波器设计培训教程
- ADS混频器仿真分析实例视频培训课程
- ADS Momentum电磁仿真设计视频课程
- ADS射频电路与通信系统设计高级培训
- ADS Layout和电磁仿真设计培训视频
- ADS Workspace and Simulators Training Course
- ADS Circuit Simulation Training Course
- ADS Layout and EM Simulation Training Course
- Agilent ADS 内部原版培训教材合集