- 易迪拓培训,专注于微波、射频、天线设计工程师的培养
Re: TSMC 0.18 RF designkit for ADS2005A
or in S parameter controller check the Z parameters
and use the Zin measurement equation
about the .OP in ELDO , in ads u can view all the operating point paramters
in any simulation controller , check detailed operating point , or details i am not so sure but is also in ADS
khouly
it's cool. The operating analysis give all most the same information as ELDO, ADS is good
thanks,everyone
does anyone know the zero-if receiver for GPS applications?
i have a project about this, does anyone offer me some good suggestions?
thanks in advance
what did you finish in the receiver?
and what is your problem?
I want to do the RF to Zero IF, but i have not the original schemetic for single compenent, such as LNA, mixer, PLL, et.al
I can't understand your problem. What schematics do you need?
Designing a receiver is a big job.
First of all, you have to make a specification, so examine the GPS physical layer. Then, make a system design. If it hasn't finished, then you don't need any schematic.
Is the model attached above an educational one or is it by any chance commercial? (I doubt it).
How can I get the commercial model?
thanks
but i want to konw it's there anyone who have TSMC 0.18 RF v6 for ADS
the same problem i happen to,so thanks for khouly's
V3 .
can we do a Lyaout using the TSMC 0.18μ in ADS, If it is the case, please show me how.
Thanks
Thanks for the help from everyone here,especially khouly and drabos! i learn a lot!
tsmc 0.18 cmos ads pdk v5a
thanks
it is update so quickly
In my @DS2005:
V2:can be installed ok.7 compoments. The moscap and juncap have some syntax errors.
V3:can be installed ok. 7 compoments. It has few syntax errors. The moscap model should be wrong. Even the nmose model is not accurate enough.
V5a: Installed ok. 20 compoments. The file from rillyxue may be not complete. Errors like "Unresolved references: R1.R_Rnodw" always be showed.
you can use designkit setup, and set the right path, everything is ok.
good luck!
thanks for the V5
I will test it.
i study this now !
thanks, guys
It is useful, i solved my problem.
refer a technology in the schematic!
by the way: does anyone have a 0.25 design kit?
How to install atf35143.zap in ads 2005A ?
申明:网友回复良莠不齐,仅供参考。如需专业帮助,请学习易迪拓培训专家讲授的ADS视频培训课程。
上一篇:patch antenna with parasatic by agilent ADS
下一篇:FET pad layout in ADS
国内最全面、最专业的Agilent ADS培训课程,可以帮助您从零开始,全面系统学习ADS设计应用【More..】
- Agilent ADS教学培训课程套装
- 两周学会ADS2011、ADS2013视频教程
- ADS2012、ADS2013射频电路设计详解
- ADS高低阻抗线微带滤波器设计培训教程
- ADS混频器仿真分析实例视频培训课程
- ADS Momentum电磁仿真设计视频课程
- ADS射频电路与通信系统设计高级培训
- ADS Layout和电磁仿真设计培训视频
- ADS Workspace and Simulators Training Course
- ADS Circuit Simulation Training Course
- ADS Layout and EM Simulation Training Course
- Agilent ADS 内部原版培训教材合集