- 易迪拓培训,专注于微波、射频、天线设计工程师的培养
Simulating Balun in ADS Schematic
I am trying to do this circuit in ADS Schematic. I have been able to find all other components. But I have not been able to find this
"3 port Balun which says Balun_device". I did find other 3 port baluns, but I would like to know under which list it will be possible to find this component.
"balun_device" I have attached the schematic.
Please help me, as I have been stuck at this point. I would deeply appreciate it.
Thanks,
Prasanna
It is a custom component.
Select this instance and then do "identify" from menu.
Can you explain more? I would greatly appreciate it if someone explains and tells me how to simulate what is in the schematic.
Thanks for replying,
Prasanna
---------- Post added at 20:37 ---------- Previous post was at 20:26 ----------
This schematic is on paper. I dont have a soft copy of the ADS program. Its from a thesis I am trying to implement.
First of all, do you understand an usage of Agilent ADS surely ?
See Balun3Port (Balun, 3-port) - ADS 2009 -*Agilent EEsof Documentation Center
Or see Fig.5 of http://www.designers-guide.org/Analysis/diff.pdf
Yes,
I am new to ADS. I did find the link you posted on the agilent website.
But is there a way, I can recreate the exact component as in the picture as in an exact way of simulating the custom component.
Thanks,
Prasanna
Again, can you understand an usage of Agilent ADS surely ?
Prasanna
that balun device is a subcircuit: inside that block there is another schematic and you cannot know from a paper what is inside.
Googling your infos, I've found this thesis:X-band Phase Shifters for Phased Array, Jean Xu, cincinnati university. Is it the one you are trying to implement, I guess.
The schematic of the balun is done using 2 lange couplers, see page 38.
I hope it can help.
Mazz
Hi Mazz,
Thanks a lot, that explains it in detail.
Yeah I have downloaded that Thesis document and did see the schematic. So my understanding is that the "sub-circuit" inside this "custom component" is the schematic given in page no. 38.
Since I am new to ADS, i did not quite understand it.Thanks again.
How do i make my own custom component in ADS? Will it be possible for you to explain that?
Thanks,
Prasanna
---------- Post added at 22:49 ---------- Previous post was at 22:48 ----------
I am sorry but I am not really sure what that question means..
Prasanna
Prasanna
you don't really need to do a subcircuit. You can place the balun at the same level of the rest of the circuit, if this is easier for you.
Mazz
申明:网友回复良莠不齐,仅供参考。如需专业帮助,请学习易迪拓培训专家讲授的ADS视频培训课程。
上一篇:Need help in Agilent ADS 2009 Avago Design Kit
下一篇:How to do via configuration in ADS
国内最全面、最专业的Agilent ADS培训课程,可以帮助您从零开始,全面系统学习ADS设计应用【More..】
- Agilent ADS教学培训课程套装
- 两周学会ADS2011、ADS2013视频教程
- ADS2012、ADS2013射频电路设计详解
- ADS高低阻抗线微带滤波器设计培训教程
- ADS混频器仿真分析实例视频培训课程
- ADS Momentum电磁仿真设计视频课程
- ADS射频电路与通信系统设计高级培训
- ADS Layout和电磁仿真设计培训视频
- ADS Workspace and Simulators Training Course
- ADS Circuit Simulation Training Course
- ADS Layout and EM Simulation Training Course
- Agilent ADS 内部原版培训教材合集