- 易迪拓培训,专注于微波、射频、天线设计工程师的培养
budget analysis in ads
how to get Budget Analysis in ADS when there are two path in receiver(I & Q).
thanks
vivek
i think u can replace the Iand Q with single path
just to calculate the total NF , gain , and IIP3
then apply the result to I and Q
khouly
Thanks khouly.
you mean to say I should consider only one path! is there any alternative of his actually i am getting error in defining second budget_path.
vivek
the second path is the same as the 1st , but the received power is divided to enter the 2 paths , so u can replace them with one path
khouly
[quote="khouly"]the second path is the same as the 1st , but the received power is divided to enter the 2 paths , so u can replace them with one path
Thanks Khouly
could you tell me how to calculate Image rejection ?it should be from I path or Q path.I am using tone of 2.44GHz for source,2.24GHz for Ist LO and 199MHz for second LO.and how to calculate IIIP3
the Image rejection ratio : ratio between the gain of the desired channel to the gain of the image signal
is ur IQ paths after the 1st mixer , then calculate the power before the I and Q spliting , of both desried and image signals
check the image
khouly
Thanks Khouly for help.
But my problem is different in my case image rejection will be done after the I-Q splitting .Here I am attaching image pls check it and suggest me.
I Have one more problem in calculating NF, NFdeg, Gain using AC analysis is that while considering only one path what shoul I do with power splitter?f I keep it at same plca then what about its third port
the image rejection ratio can be calculated after the power combining , just before the BPF
i see ur using one of image rejection achitectures
about the noise figure and IIP3 , check the RF system design guide , and try to build ur own equations
specially ur architecture need alot of work to be created that way
khouly
Use equations to to RF cascaded budget analysis
he can use the budget simulation in ADS , he need to use equations and AC and HB enginers
khouly
Khouly,
can you explain me what is ".t1",and ".t2" in equation format for the equation like
budget_path=["port1.t1","a1_amp.t2".................etc]
send me , the project , u created , so i can check the equations
or tell me the steps , to create such a project
khouly
hello khouly,
can you send me your Email ID?
vivek
hello ,
now my problem has been solved.
can some one provide me RF design specification of bluetooth i am not able to get from bluetooth .org
thanks
vivek
申明:网友回复良莠不齐,仅供参考。如需专业帮助,请学习易迪拓培训专家讲授的ADS视频培训课程。
上一篇:Better results in ADS ?
下一篇:Filter design using spiral inductor in ADS Plz Help
国内最全面、最专业的Agilent ADS培训课程,可以帮助您从零开始,全面系统学习ADS设计应用【More..】
- Agilent ADS教学培训课程套装
- 两周学会ADS2011、ADS2013视频教程
- ADS2012、ADS2013射频电路设计详解
- ADS高低阻抗线微带滤波器设计培训教程
- ADS混频器仿真分析实例视频培训课程
- ADS Momentum电磁仿真设计视频课程
- ADS射频电路与通信系统设计高级培训
- ADS Layout和电磁仿真设计培训视频
- ADS Workspace and Simulators Training Course
- ADS Circuit Simulation Training Course
- ADS Layout and EM Simulation Training Course
- Agilent ADS 内部原版培训教材合集