- 易迪拓培训,专注于微波、射频、天线设计工程师的培养
class f pa ads
录入:edatop.com 点击:
Hello to all,
I am very new to RF designing and I am a student... I am designing a class F PA for LINC TX(outphasing transmitter), I am using cadence spectra tool to design PA and I have couple of questions...
1. how to simulate the envelope simulation using spectra... since my PA is for EDGE communication standard so I have to respect the Mask, so I have to see whether my PA output spectrum is meeting the EDGE mask or not, in cadence how to generate the I/Q baseband signal and do rest of the signal processing the feed it to my PA. I suppose this is possible through matlab+Virtuoso AMS+simulink coupler, but I don't have license for AMS tool. is there any other way to generate the baseband signal. I have ADS tool (since I don't have STM models file for ADS so I can't use ADS) lets say I will generate the baseband signal from ADS and save it into .dat file, so does it is possible i can use this .dat file into cadence to simulate envelope simulation.
2. is there any other way to check my PA linearity... since my PA is switched kind of amp(not linear like A, B, AB and C) so I can't sweep my input signal power (which is fixed 1.2V square pulse coming from divider ckt after VCO) and also this is a large signal, but PSS and PSS + PAC simulation is only for small signal... looking into these fact dose IIP3 or ACPR are making any sense to switch PA amplifier (these spec is for linear PA I suppose), so how do I check my output mask requirement. can I do two tone test using pss (I can apply two tone spaced by 200kHz channel small signal into my vco and check the IP3 IP5 etc... using pss simulation and if results are good I can assume my PA will meet the mask...
3. what is the diff between ip3, ip5.. and ACPR...
4. how do I check the stability of my switched PA if my input is not small signal and I can't sweep it (input is a pulse of 1.2V peak).
I have some more question but since this mail is too long so I will ask in different topic...
thanks in advance for positive replay...
Amit
I am very new to RF designing and I am a student... I am designing a class F PA for LINC TX(outphasing transmitter), I am using cadence spectra tool to design PA and I have couple of questions...
1. how to simulate the envelope simulation using spectra... since my PA is for EDGE communication standard so I have to respect the Mask, so I have to see whether my PA output spectrum is meeting the EDGE mask or not, in cadence how to generate the I/Q baseband signal and do rest of the signal processing the feed it to my PA. I suppose this is possible through matlab+Virtuoso AMS+simulink coupler, but I don't have license for AMS tool. is there any other way to generate the baseband signal. I have ADS tool (since I don't have STM models file for ADS so I can't use ADS) lets say I will generate the baseband signal from ADS and save it into .dat file, so does it is possible i can use this .dat file into cadence to simulate envelope simulation.
2. is there any other way to check my PA linearity... since my PA is switched kind of amp(not linear like A, B, AB and C) so I can't sweep my input signal power (which is fixed 1.2V square pulse coming from divider ckt after VCO) and also this is a large signal, but PSS and PSS + PAC simulation is only for small signal... looking into these fact dose IIP3 or ACPR are making any sense to switch PA amplifier (these spec is for linear PA I suppose), so how do I check my output mask requirement. can I do two tone test using pss (I can apply two tone spaced by 200kHz channel small signal into my vco and check the IP3 IP5 etc... using pss simulation and if results are good I can assume my PA will meet the mask...
3. what is the diff between ip3, ip5.. and ACPR...
4. how do I check the stability of my switched PA if my input is not small signal and I can't sweep it (input is a pulse of 1.2V peak).
I have some more question but since this mail is too long so I will ask in different topic...
thanks in advance for positive replay...
Amit
申明:网友回复良莠不齐,仅供参考。如需专业帮助,请学习易迪拓培训专家讲授的ADS视频培训课程。
上一篇:How to draw via by using ADS momentum?
下一篇:Subtracting the output of the polyphase filter in ADS
ADS培训课程推荐详情>>
国内最全面、最专业的Agilent ADS培训课程,可以帮助您从零开始,全面系统学习ADS设计应用【More..】
- Agilent ADS教学培训课程套装
- 两周学会ADS2011、ADS2013视频教程
- ADS2012、ADS2013射频电路设计详解
- ADS高低阻抗线微带滤波器设计培训教程
- ADS混频器仿真分析实例视频培训课程
- ADS Momentum电磁仿真设计视频课程
- ADS射频电路与通信系统设计高级培训
- ADS Layout和电磁仿真设计培训视频
- ADS Workspace and Simulators Training Course
- ADS Circuit Simulation Training Course
- ADS Layout and EM Simulation Training Course
- Agilent ADS 内部原版培训教材合集