ORCAD 如何生成POWERPCB5.0的网表？

找个PCBNAV3.3或4.0之类的软件来转换网络表即可。

用PCBNAV後,會出現Orcad9.0人打印功能不行.要求輸入x_和y_的什值.
請教！其它功能正常.

其实可以不用管那么多的,只要调入的元件,网表没问题就可以了.
powerpcb与ORCAD之间是存在一些问题的,调入时会提示一些无聊的错误.

是这样吗?我也发现这个问题。不知道是不是不正常。

*PADS-PCB**PART*C1 0805@0805C10 c1206@c1206C11 CAP1@CK05C12 CAP1@CK05C13 CAP1@CK05C14 10UF@10UFC15 CAP1@CK05C2 0805@0805C3 0805@0805C4 0805@0805C5 0805@0805C6 c1206@c1206C7 c1206@c1206C8 c1206@c1206C9 c1206@c1206J1 SIP-6P@SIP-6PJ2 SIP-8P@SIP-8PJ3 SIP-3P@SIP-3PJ4 SIP-2P@SIP-2PP1 DCON9F@DCON9FP2 DCON9F@DCON9FP3 DCON9F@DCON9FR1 R1@R1/8WR2 R1@R1/8WR3 R1@R1/8WR4 R1@R1/8WR5 VRES1@VRESR6 R1@R1/8WSW1 SWITCH@SWITCHSW2 SWITCH@SWITCHSW3 SWITCH@SWITCHSW4 SWITCH@SWITCHU1 MAX232@DIP16U2 MAX232@DIP16U3 DIP8@DIP8U4 SO40M1@SO40M1U5 SOJ20@SOJ20U6 DIP8@DIP8Y1 CAP1@CK06Y2 CAP1@CK06

*NET**SIGNAL* N00416C4.1 U2.4*SIGNAL* DIOU4.22 J4.1*SIGNAL* N00419C4.2 U2.5*SIGNAL* N00436U2.6 C7.2*SIGNAL* DOUTU4.23 J4.2*SIGNAL* KEY1R3.1 SW1.2*SIGNAL* N00410C2.2 U2.3*SIGNAL* KEY2R2.1 SW2.2*SIGNAL* KEY3R1.1 SW3.2*SIGNAL* N00398C2.1 U2.1*SIGNAL* KEY4R4.1 SW4.2*SIGNAL* RCRSTR6.2 J3.1 C14.2*SIGNAL* RSTU4.9 J3.2*SIGNAL* WTRSTJ3.3 U3.7*SIGNAL* N11632C1.2 U1.3*SIGNAL* N11649C1.1 U1.1*SIGNAL* N11661C3.1 U1.4*SIGNAL* N11664C3.2 U1.5*SIGNAL* N11679U1.6 C5.2*SIGNAL* N00374J1.4 R5.1*SIGNAL* N11868J1.5 R5.2*SIGNAL* N01837U4.10 U5.12*SIGNAL* V2VU1.2 C9.1*SIGNAL* N01840U4.11 U5.13*SIGNAL* V1VU2.2 C10.1*SIGNAL* N01843U4.13 U5.15*SIGNAL* N01846U4.14 U5.16*SIGNAL* N01849U4.15 U5.17*SIGNAL* N01852U4.16 U5.18*SIGNAL* R232TXD1P3.2 U2.14*SIGNAL* R232RXD1P3.3 U2.13*SIGNAL* R232RXD2U2.8 P1.3*SIGNAL* R232TXD2U2.7 P1.2*SIGNAL* R232TXD3P2.2 U1.14*SIGNAL* R232RXD3P2.3 U1.13*SIGNAL* N00201U3.8 U3.1*SIGNAL* WDIU4.21 U3.6*SIGNAL* TXD3U5.5 U1.11*SIGNAL* RXD3U5.6 U1.12*SIGNAL* TXD2U5.8 U2.10*SIGNAL* TXD1U5.3 U2.11*SIGNAL* RXD1U5.4 U2.12*SIGNAL* RXD2U5.9 U2.9*SIGNAL* N01197R4.2 U4.36*SIGNAL* JRJ1.6 R5.3*SIGNAL* N01191R2.2 U4.38*SIGNAL* N0000332U4.39 R3.2*SIGNAL* N01194R1.2 U4.37*SIGNAL* D8U4.8 J2.8*SIGNAL* N00302J2.1 U4.1*SIGNAL* N00308U4.2 J2.2*SIGNAL* N00314U4.3 J2.3*SIGNAL* N00320U4.4 J2.4*SIGNAL* N00761U4.17 U5.19*SIGNAL* N00326U4.5 J2.5*SIGNAL* N00332J2.6 U4.6*SIGNAL* N00338U4.7 J2.7*SIGNAL* N00401J1.2 U4.27*SIGNAL* OSCIY2.1 U5.1 C15.2*SIGNAL* OSCOY2.2 U5.2 C13.2*SIGNAL* N00407J1.1 U4.26*SIGNAL* N01535U4.12 U5.14*SIGNAL* N00395J1.3 U4.28*SIGNAL* GNDU2.15 U4.20 U1.15 U3.3 U6.4 U3.4 C6.2 C8.2U5.11 U5.10*SIGNAL* VCCU2.16 U4.40 U1.16 U6.8 C14.1 U3.2 C5.1 U4.31C9.2 C10.2 C6.1 C8.1*SIGNAL* GND_POWERU6.7 U6.3 U5.20 SW2.1 P3.5 P2.5 SW3.1 C15.1C7.1 U6.2 U6.1 SW4.1 SW1.1 C13.1 P1.5*SIGNAL* SCLKU6.6 U4.25*SIGNAL* SDAU6.5 U4.24*SIGNAL* N00024C11.1 C12.1 R6.1*SIGNAL* N00015C11.2 Y1.2 U4.19*SIGNAL* N00018Y1.1 U4.18 C12.2*END*

重要的是在ORCAD的元件FOOTPRINT中填入POWERPCB库中有的文件。

上面有很多是我自己建的。