S.O.S - gerber out

想請問各位大大～～
GERBER OUT 出現下列訊息 , 要怎麼解決呢?
Results from parameter file ...
    DEVICE-TYPE           GERBER_RS274X
    OUTPUT-UNITS          INCHES
    FILM-SIZE             4000000 4000000
    FORMAT                5.5
    ABORT-ON-ERROR        NO
    SCALE                 1
    SUPPRESS-LEAD-ZEROES  YES
    SUPPRESS-TRAIL-ZEROES NO
    SUPPRESS-EQUAL        YES
    UNDEF-APT-CONT        YES

FILM PARAMETERS :
  ---------------------------------------------------------
  Undefined line width                10.000
  Mirror code                         NONE
  Rotate angle                        NONE
  Offset x:                           0.000
  Offset y:                           0.000
  Plot negative                       NO
  Suppress unconnected internal pads  DYNAMIC
  Draw holes only                     NO
    WARNING: Segment with same start and end points at
        (782.551 -173.437) will be ignored. Increasing output
        accuracy may allow segment to be generated.
    WARNING: Segment with same start and end points at
        (854.846 -173.420) will be ignored. Increasing output
        accuracy may allow segment to be generated.
    WARNING: Segment with same start and end points at
        (1002.446 -168.420) will be ignored. Increasing output
        accuracy may allow segment to be generated.
    WARNING: Segment with same start and end points at
        (1672.203 -346.515) will be ignored. Increasing output
        accuracy may allow segment to be generated.
    WARNING: Segment with same start and end points at
        (1652.601 -163.938) will be ignored. Increasing output
        accuracy may allow segment to be generated.
    WARNING: Segment with same start and end points at
        (3599.143 -219.998) will be ignored. Increasing output
        accuracy may allow segment to be generated.
    WARNING: Segment with same start and end points at
        (3595.000 -970.855) will be ignored. Increasing output
        accuracy may allow segment to be generated.
    WARNING: Segment with same start and end points at
        (2840.002 -1200.000) will be ignored. Increasing output
        accuracy may allow segment to be generated.
    WARNING: Segment with same start and end points at
        (2620.002 -1310.000) will be ignored. Increasing output
        accuracy may allow segment to be generated.
    WARNING: Segment with same start and end points at
        (2744.143 -1124.998) will be ignored. Increasing output
        accuracy may allow segment to be generated.
    WARNING: Segment with same start and end points at
        (2654.145 -1050.000) will be ignored. Increasing output
        accuracy may allow segment to be generated.
    WARNING: Segment with same start and end points at
        (2600.857 -1050.002) will be ignored. Increasing output
        accuracy may allow segment to be generated.
    WARNING: Segment with same start and end points at
        (2584.998 -960.857) will be ignored. Increasing output
        accuracy may allow segment to be generated.
    WARNING: Segment with same start and end points at
        (2480.002 -1164.143) will be ignored. Increasing output
        accuracy may allow segment to be generated.
    WARNING: Segment with same start and end points at
        (2469.145 -1175.000) will be ignored. Increasing output
        accuracy may allow segment to be generated.
    WARNING: Segment with same start and end points at
        (2415.857 -1175.002) will be ignored. Increasing output
        accuracy may allow segment to be generated.
    WARNING: Segment with same start and end points at
        (2234.145 -1095.000) will be ignored. Increasing output
        accuracy may allow segment to be generated.
    WARNING: Segment with same start and end points at
        (2155.857 -1095.002) will be ignored. Increasing output
        accuracy may allow segment to be generated.
    WARNING: Segment with same start and end points at
        (2145.000 -1084.145) will be ignored. Increasing output
        accuracy may allow segment to be generated.
    WARNING: Segment with same start and end points at
        (2144.998 -1020.000) will be ignored. Increasing output
        accuracy may allow segment to be generated.
    WARNING: Segment with same start and end points at
        (2130.857 -890.002) will be ignored. Increasing output
        accuracy may allow segment to be generated.
    WARNING: Segment with same start and end points at
        (2119.998 -824.873) will be ignored. Increasing output
        accuracy may allow segment to be generated.
    WARNING: Segment with same start and end points at
        (1990.000 -905.855) will be ignored. Increasing output
        accuracy may allow segment to be generated.
    WARNING: Segment with same start and end points at
        (2019.998 -900.857) will be ignored. Increasing output
        accuracy may allow segment to be generated.
    APERTURES USED:
  ---------------------------------------------------------
  TYPE       SIZE/NAME                   ROT   MIRROR MODE
  ---------------------------------------------------------
  CIRCLE     0.00400                                  DARK
  CIRCLE     0.00450                                  DARK
  CIRCLE     0.00500                                  DARK
  CIRCLE     0.00600                                  DARK
  CIRCLE     0.01000                                  DARK
  CIRCLE     0.01500                                  DARK
  CIRCLE     0.01800                                  DARK
  CIRCLE     0.02000                                  DARK
  CIRCLE     0.02200                                  DARK
  CIRCLE     0.02400                                  DARK
  CIRCLE     0.03937                                  DARK
  CIRCLE     0.05100                                  DARK
  CIRCLE     0.05500                                  DARK
  CIRCLE     0.06300                                  DARK
  CIRCLE     0.12600                                  DARK
  SQUARE     0.02165                     0.000 NO     DARK
  SQUARE     0.04000                     0.000 NO     DARK
  SQUARE     0.05000                     0.000 NO     DARK
  SQUARE     0.05500                     0.000 NO     DARK
  RECTANGLE  0.02400     x 0.03100       0.000 NO     DARK
  RECTANGLE  0.02400     x 0.03100      90.000 NO     DARK
  RECTANGLE  0.03900     x 0.06100      90.000 NO     DARK
  RECTANGLE  0.03937     x 0.02402       0.000 NO     DARK
  RECTANGLE  0.03937     x 0.03150       0.000 NO     DARK
  RECTANGLE  0.03937     x 0.03150      90.000 NO     DARK
  RECTANGLE  0.03937     x 0.03150     179.939 NO     DARK
  RECTANGLE  0.04000     x 0.05000       0.000 NO     DARK
  RECTANGLE  0.04000     x 0.05000      90.000 NO     DARK
  RECTANGLE  0.04000     x 0.06000       0.000 NO     DARK
  RECTANGLE  0.05000     x 0.04000       0.000 NO     DARK
  RECTANGLE  0.05000     x 0.04000      90.000 NO     DARK
  RECTANGLE  0.06400     x 0.06000       0.000 NO     DARK
  RECTANGLE  0.09400     x 0.06500       0.000 NO     DARK
  RECTANGLE  0.09400     x 0.06500      90.000 NO     DARK
  RECTANGLE  0.09500     x 0.02400       0.000 NO     DARK
  PAD SHAPE  SHA_R60X100               180.000 NO     DARK
  PAD SHAPE  SHA_O60X100               180.000 NO     DARK
     SOLDER created with warnings

------------------------------------------------------
SUMMARY:
        SOLDER created with warnings
ARTWORK had warnings

FILM-SIZE 改小,再試試. 預設X:24; Y:16

不理，

還是一樣

還是一樣

WARNING: Segment with same start and end points at (1990.000 -905.855) will be ignored. Increasing output accuracy may allow segment to be generated.
WARNING: Segment with same start and end points at (2019.998 -900.857) will be ignored. Increasing output accuracy may allow segment to be generated.
那幾個位置應該有一點的線段(因為開始的位置和結束的位置是一樣),找到該位置,並將它刪除,試試看

我查過了,都不是線段都是SHAPE ～～ 才不知要從何刪起

没问题的

這種問題不需要理會 , 別想太多.

同意不理会这个问题  你用350看一下光绘文件有没有问题，跑一下最小线间距能达到工艺要求，基本都ok，感觉16.x以上的出gerber好严格，总是报一大堆的警告出来